PHY cli Command

[zh_CN]

Important

All functionalities on this page are designed for users who are still using CLI commands to operate PHY.

• rfcali_show_data :Display calibration information

• tempd :Get the current chip temperature

• rxsens :WIFI radio frequency receiver test command

• txevm :WiFi channel transmission test command

rfcali_show_data :Display calibration information

Command

rfcali_show_data

Params

none

Usage Scenario

rfcali_show_data: Input this command to start displaying the calibration information of the board.

Response

CMDRSP:OK

CMDRSP:ERROR

Note

This command takes effect under the condition that CONFIG_WIFI_CLI_ENABLE is enabled.

tempd :Get the current chip temperature

Command

tempd [stop]

Params

stop:Turn off temperature compensation

Usage Scenario

1)  input：
        tempd:Return the current temperature

           get temperature 581

           current temperature is 581

2)  input:
        tempd stop :Turn off temperature compensation

Response

CMDRSP:OK

CMDRSP:ERROR

Note

This command takes effect under the condition that CONFIG_WIFI_CLI_ENABLE is enabled

rxsens :WIFI radio frequency receiver test command

Command

rxsens [-b] [-c] [-d]

Params

-d: Timer interval (unit:s)

-c: Channel

-b: Bandwidth 0:20M, 1:40M

Usage Scenario

rxsens -e 1 Enter rx test mode.

rxsens -b 0 -c 1 -d 1       Channel 1 with a 20M bandwidth receiver

rxsens -b 0 -c 7 -d 1       Channel 7 with a 20M bandwidth receiver

rxsens -b 0 -c 13 -d 1      Channel 13 with a 20M bandwidth receiver

rxsens -b 0 -c 14 -d 1      Channel 14 with a 20M bandwidth receiver

rxsens -b 0 -c 14 -d 1      Channel 14 with a 20M bandwidth receiver(manual testing only)

rxsens -b 1 -c 3 -d 1       Channel 3 with a 40M bandwidth receiver

rxsens -b 1 -c 7 -d 1       Channel 7 with a 40M bandwidth receiver

rxsens -b 1 -c 11 -d 1      Channel 11 with a 40M bandwidth receiver

rxsens -b 1 -c 14 -d 1      Channel 14 with a 40M bandwidth receiver

rxsens -b 1 -c 14 -d 1      Channel 14 with a 40M bandwidth receiver(manual testing only)

rxsens -g 0 Reset count of the packages to zero.

rxsens -s 1 Start calculating the package

rxsens -s 0 Stop calculating the package

rxsens -g 1 Obtain 20M bandwidth correctly packet(correctly packets/1000,The requirements for passing the test：11b：>92%;others:>90%。)

rxsens -g 2 Obtain 40M bandwidth correctly packet(correctly packets/1000,The requirements for passing the test：>90%。)

rxsens -e 0 Exit rx test mode.

Response

CMDRSP:OK

CMDRSP:ERROR

Note

This command takes effect under the condition that CONFIG_WIFI_CLI_ENABLE is enabled

txevm :WiFi channel transmission test command

Command

txevm [-b] [-r] [-c] [-f]

Params

-b: Bandwidth 0:20M; 1:40M

-r: Rate

-c: Channel

-f : 0x0: Non-HT; 0x1:Non-HT-DUP; 0x2: HT-MM;  0x3: HT-GF

Usage Scenario

//11M power test
txevm -b 0 -r 11 -c 1       11M Channel 1 transmission
txevm -b 0 -r 11 -c 7       11M Channel 7 transmission
txevm -b 0 -r 11 -c 13      11M Channel 13 transmission

//54M power test
txevm -b 0 -r 54 -c 1       54M Channel 1 transmission
txevm -b 0 -r 54 -c 7       54M Channel 7 transmission
txevm -b 0 -r 54 -c 13      54M Channel 13 transmission

//HT20 65M power test
txevm -b 0 -r 135 -c 1 -f 2     65M Channel 1 transmission
txevm -b 0 -r 135 -c 7 -f 2     65M Channel 7 transmission
txevm -b 0 -r 135 -c 13 -f 2        65M Channel 13 transmission

//HT40 135M power test
txevm -b 1 -r 135 -c 3 -f 2     135M Channel 3 transmission
txevm -b 1 -r 135 -c 7 -f 2     135M Channel 7 transmission
txevm -b 1 -r 135 -c 11 -f 2        135M Channel 11 transmission

Response

CMDRSP:OK

CMDRSP:ERROR

Note

This command takes effect under the condition that CONFIG_WIFI_CLI_ENABLE is enabled